Windows for Energy Efficiency

Nothing is more important when designing your home than the window & door selection. The 3 most important ‘S’ factors to consider are: Sustainability (Energy Efficiency), Style and Security. The whole character and thermal performance of your home will be decided by the choices you make at the design phase.

As published from Australia Windows Association  – Energy Efficient Doors and Windows, Energy Efficient Homes

Introduction
Technological advances in the last 25 years have made it possible to design windows which insulate against heat and cold up to four times better than conventional windows. Dramatic improvements in sound insulation are possible. To a point, similar technologies can serve both needs.

This Technical Note summarises the objectives, the technical solutions and the trade-offs that building designers and industry need to understand.

Energy Efficiency
An energy-efficient window is one that helps to minimise the use of artificial heating and cooling in a building. In many parts of Australia, the priority is to keep solar heat out of the home, except during colder months, when ‘free’ solar heat gain and retention of warmth in the house become important.

Heat gain or heat loss take three forms: radiant heat transfer, conductive heat transfer and heat transfer via air infiltration. Ideally, this calls for strong solar protection on east and west windows, but deliberate use of free sunlight (via clear glass) from northerly windows. This means different window solutions for different orientations.

Alternatively, it is possible to use the same uniform high-performance window type on all sides of a home – provided it is correctly chosen. From an energy point of view, this is not quite optimal but it simplifies the specification process and still results in very substantial energy savings and improved comfort, compared to using clear single-glazed windows.

Low U-value
In most climates, windows with at least four heating or four cooling stars, on all sides of the house, will ensure that conductive heat losses and heat gains are minimised. This means the windows must have a low U-value. It is possible to reduce the glazing U-value by means of single glazing having a low-e coating.

Low-e coatings are near-invisible. While a low-e coating on simple single glazing reduces that part of the heat transfer which is due to radiation, it does nothing to reduce conductive and convective heat flow.

A much better solution is to reduce all three forms of heat transfer. To do this an insulating glass unit (IGU) is required. The IGU is the vehicle for all high-performance windows, in all climates – hot, cold and mixed. The IGU should preferably have some sort of low-e coating on at least one pane and have argon gas fill between the panes, to give the lowest overall heat transfer. U-values as low as 1.8 are possible, compared with about 5 in the case of a single-glazed clear window.

To complement the glazing system, a frame with a low U-value assists in reducing the whole-window U-value. Frames that use thermal breaks or composite metal / timber design, or timber or uPVC frames, outperform standard aluminium windows. This frame performance difference shows up in the WERS stars as an extra half star or so.

The most common filling gas between the panes of an IGU is dry air. The narrowest air gap used is 6 mm but this should be avoided unless there is no alternative. The use of wider gaps (10-20 mm) will improve the U-value and increase the WERS heating star rating by at least half a star. Contrary to common belief, a very wide air gap is not disadvantageous, apart from being impractical for an IGU.

Although convection cells are bigger and more active, this is counteracted by the greater thickness of air which provides additional resistance to conduction. The use of (cheap) argon gas instead of air in the IGU space lifts the heating rating by about a third to half a star in most cases. Table 1, the WERS table of Generic Windows, gives indicative performance.

Wider gaps also give better acoustic insulation. For more information on acoustics, click here.

High versus Low Solar Heat Gain Coefficient: Low-e Coatings
As mentioned, all low-e coatings assist energy efficiency by suppressing radiation heat transfer. This means they act like ‘heat mirrors’ and reflect heat back into a room in winter, which reduces the amount lost to the outside.

Some low-e coatings are essentially transparent to solar radiation; these mostly take the form of so-called ‘hard’ or ‘pyrolytic’ coatings. They are best suited to cooler climates or on the north side of a building where ‘free’ winter heating can be exploited.

Other low-e coatings (frequently referred to as ‘soft’, ‘multilayer’ or ‘spectrally selective’ coatings) are available, which block up to half the invisible, radiant solar heat while still preserving daylight. Windows with spectrally selective low-e coatings reduce the solar heat gain coefficient (SHGC) by up to 60% compared with clear 3 mm glass. This reduces or in some cases eliminates the need for wide eaves or shading systems.

When the Generic Table was developed, spectrally selective low-e coatings were unusual on the Australian market. However their performance is well approximated by windows 22 – 27 in the table, which achieve similar results by a different construction.

 

Image courtesy of University of Minnesota

 

Good Weather Seals

Heat leaves or enters a home through gaps and cracks around sashes and frames. When a window is shut it should be shut. WERS-rated windows must satisfy Australian Standard AS 2047 for air infiltration performance. Most easily exceed it and achieve air leakage figures below 1 litre per second per square metre of window area.

Traditionally, windows with compression seals, as fitted to awning and casement windows, tended to have superior long-term infiltration performance. However recent advances in some sliding window seals have reduced the gap. The difference between a window that just meets AS 2047 (5 L/s.m2) and a very tight window is about half a heating star. The effect on cooling performance is much less.

© Australian Window Association & Window Energy Rating Scheme

SWA Climate Zone Guides

SWA – Climate Zones 1, 2 & 3 (2071 KB)
Northern Australia, Brisbane and Darwin

SWA – Climate Zones 4 & 5 (1937 KB)
Sydney, Perth and Adelaide

SWA – Climate Zones 6, 7 & 8 (1919 KB)
Most of Victoria, ACT, Tasmania and Southern parts of NSW and WA